Overview
The steps a service partner follows on site to install a FUYL Smart Locker, and later remove it. Site IT usually onboards the locker with ForwardPass, and facilities look after power and the wall. Who does what, and what to check before the visit, are in the full runsheet.
Warning: A large FUYL Locker is around 90kg (200lb), and a small one around 40kg (90lb). Always move and stand one up with two people.
What to bring
- A second person.
- A trolley, pallet jack or furniture dolly that can take the locker's weight.
- A box cutter and gloves.
- The model's Quick Start Guide (see Quick Start Guides).
- Charging cables for a FUYL Tower, if the order doesn't include them. A FUYL 8 or 23 has its cables built in.
Install and onboard
1. Receive the delivery
- Check the delivery Count the boxes against the delivery note, and photograph any damage before signing.
- Note the serial numbers Write down each locker's serial number and MAC addresses from the packaging.
2. Move it to its site
- Check the route Make sure the boxed locker fits through every doorway and lift on the way.
- Keep it boxed Leave it in its packaging until it's at its final spot, to protect the doors and display.
3. Unbox it and stand it up
- Unpack it in place Follow the Quick Start Guide, as close to the final spot as possible.
- Stand it up One person lifts from the top while the other steadies the base. Avoid lifting by the doors or display, as they aren't built to take its weight.
- Find the accessories The power cable, keys and bay blinds are sometimes packed inside a locked bay (the Quick Start Guide shows how to get them out).
- Look it over Photograph any damage, and keep the side access door keys safe for the customer.
4. Secure it to the wall
Warning: An unsecured locker can tip forward. Secure it before the Kiosk mount goes on or anything's loaded.
- Position it Move it against the wall site facilities has prepared, with room for the side access door to open.
- Level it Adjust the feet until it's level, while a second person keeps it steady.
- Secure it Attach it to the wall fixings with the included hardware (or the optional Wall Mount Kit on a FUYL Tower 5).
- Route the cables Run the power cable (and Ethernet, if used) to the outlet, out of sight. Leave it unplugged for now.
If the wall isn't ready, stop here and let site facilities and ForwardPass know.
5. Install the Kiosk mount
Have site IT prepare the iPad first, since the mount covers its top button. Then follow the Kiosk Kit's printed instructions, or FUYL Kiosk Physical Installation.
- Fit the mount Remove the side access door's handle, then bolt on the mount support and iPad holder.
- Install the iPad Fit the iPad, and route its charging cable inside the door.
- Close up Close and lock the side access door. On a FUYL Tower 5 or 15, plug the iPad into its charger and the second outlet.
Note: Site IT usually onboards the locker with ForwardPass (stages 6 to 9), and in that case the service partner's part stops here: skip to Hand over. Sometimes ForwardPass goes through onboarding with the service partner instead, and the stages below cover that.
6. Power on and onboard
Start the video call with ForwardPass, and have site IT on hand. Site IT signs in to the Kiosk with their own Admin profile, so there's no need to know their password.
- Power on the locker Connect Ethernet (if used), plug it in and switch it on at the wall.
- Check the display It's ready once it shows Ready to set up with a unique ID.
- Sign in to the Kiosk Site IT signs in to the FUYL Kiosk app, then selects Set up new station.
- Pair the locker Choose the Locker ID shown on the display, pick the network settings, and enter the agreed Site Name and Group Name.
- Confirm it's set up The display shows a white LocknCharge logo and the bay lights glow a dim blue. The Kiosk shows No workflow detected until workflows are allocated.
7. Allocate workflows
- Allocate workflows On the Kiosk, select Allocate workflows, authenticate, and pick the agreed workflow for each bay.
8. Load devices (if required)
- Start loading On the Kiosk, select Load devices and authenticate.
- Load each device Follow the prompts, connect each device's charging cable, and shut each door firmly.
9. Test each workflow
- Run each workflow Sign in as a test user and run each workflow once (for example, borrow and return a device).
- Check the bays Make sure each bay opens, its light changes, and devices charge.
- Tidy up End any test loans or sessions, and make sure every loaded device is back in its bay.
10. Hand over
- Hand over the keys Give the side access door keys to the customer's nominated contact.
- Let ForwardPass know Reply to the support request with the serial number, location and a few photos (plus the Site Name and Group Name, if it was onboarded).
Remove a locker
1. Open and clear every bay
Important: Anything left in a locker leaves with it, so agree with site IT where every device goes first.
- End active workflows Ask site IT or ForwardPass to end any active loans, repairs or charging sessions.
- Unlock each bay On the Kiosk, select the cog , authenticate, select View tower, then Unlock bay for each bay.
- Remove the devices Hand every device to site IT, and close each bay once it's empty. The locker's own cables and bay blinds stay with it.
If the locker or Kiosk is offline, use the manual release pins behind the side access door (see Accessing Bays as an Administrator).
2. Remove it from the account
- Confirm removal Check with ForwardPass that the locker has been removed from the customer's account before going any further.
3. Factory reset the locker
Removing it from the account may already have reset it, but resetting it again is safe.
- FUYL 8 and FUYL 23: Open the side access door, pull the display door release pin and open the display door. Hold the reset button on its back for 10 to 15 seconds.
- FUYL Tower and FUYL Tower Pro: Press 00 then OK, enter an admin PIN, then select Danger zone > Factory reset and OK.
Once it restarts, check the display shows Ready to set up.
4. Power it down
- Switch off the locker Switch it off at the wall and unplug it, along with the Ethernet cable and (on a FUYL Tower 5 or 15) the iPad's charger.
5. Remove the Kiosk iPad and mount
- Take out the iPad Unlock the side access door, remove the iPad from its holder, and hand it to site IT (it stays with the customer).
- Remove the mount Unbolt the holder and support, and refit the original handle if it was kept.
- Keep the parts together Bag up the mount, bolts, cable and keys.
6. Detach it from the wall
Warning: Once the wall hardware's off, there's nothing stopping the locker tipping, so have one person steady it while the other works.
- Detach it Undo the wall hardware and ease the locker away from the wall.
7. Remove it from site
- Lock it up Close every bay and lock the side access door.
- Protect it Repack or wrap it to protect the doors and display.
- Move it safely Use two people and a trolley or pallet jack, and take the power cable, mount and kits with it.
- Check what's next Confirm with ForwardPass where the locker goes before collection, and don't dispose of it without that confirmation.