Overview
This runsheet covers what a service partner does on site to install a FUYL Smart Locker, and (eventually) remove it again. Onboarding the locker to the customer's FUYL Portal account is usually done by the site's IT team with ForwardPass, though sometimes the service partner goes through it with ForwardPass instead. Site IT and facilities look after the account, network, power and walls.
It's written to be followed in order, and each stage ends with a quick check before moving on. It covers FUYL Smart Lockers on FUYL Enhanced, used with a FUYL Kiosk (an iPad mounted on the locker). If unsure which locker is on site, see Identify a Smart Locker.
Who does what
| Party | Responsible for |
|---|---|
| Service partner (on site) | Receiving the locker, moving and unboxing it, standing it up, securing it to the prepared wall, fitting the Kiosk mount, and handing over. Sometimes onboarding, testing and loading devices too, with ForwardPass. Later, removing it. |
| ForwardPass (remote) | Preparing workflows with the customer, joining a video call during onboarding and testing, diagnosing anything that goes wrong, and removing the locker from the customer's account if asked. |
| Site IT | The customer's FUYL Portal account and Admin sign-in, network access (Ethernet or Wi-Fi, and firewall rules), the Kiosk iPad, test users, and a test device. Usually onboarding the locker, allocating workflows and testing, with ForwardPass. |
| Site facilities | Power, preparing the wall (drilling and fixings), and access to the site and the locker's final spot. |
Note: ForwardPass recommends giving service partner staff the Technician role in the customer's FUYL Portal. It's enough to load and collect devices, open bays and restart lockers, without access to workflow or account settings. Setting up a new locker on the Kiosk does need an Admin, so site IT signs in for that part. See Roles and Permissions.
Before the visit
Run through these with the customer and ForwardPass before booking a date. Most second trips come down to one of them being missed.
| Check | Who | Details |
|---|---|---|
| Location chosen | Site facilities | Indoors, dry and out of direct sunlight, ideally somewhere public and well trafficked. Leave room for the side access door to open fully, and keep the ventilation holes clear. See FUYL Locker Heat and Ventilation. |
| Wall prepared | Site facilities | A wall strong enough to hold the locker, drilled and fitted with suitable fixings for the locker's wall hardware. Lockers are secured to a wall, not the floor. |
| Power | Site facilities | An outlet close to the locker, ideally behind or above it so the plug's out of sight. A FUYL Tower 5 or 15 needs a second outlet for the Kiosk iPad (a FUYL 8 or 23 only needs the one). Any electrical work is done by an electrician before installation day. Charging can draw up to 1000W (110V) or 1800W (240V), so a shared or busy circuit isn't ideal. |
| Network | Site IT | An Ethernet port near the locker (preferred) or Wi-Fi, plus Wi-Fi for the Kiosk iPad. Outbound traffic is allowed as listed in FUYL Networking Requirements. The locker's MAC addresses are on its packaging, or ForwardPass can send them ahead of delivery. |
| FUYL Portal account | Site IT, ForwardPass | The customer's account is set up, and someone from site IT with an Admin profile is on site (or on the call) to sign in to the Kiosk. |
| Kiosk iPad | Site IT | An iPad (7th to 11th generation, or iPad Pro 11-inch) on iPadOS 17.5 or later, with the FUYL Kiosk app installed. For a FUYL Tower 5 or 15, a USB-C wall charger too. If it's managed by MDM, the app and Bluetooth are allowed. |
| Workflows ready | Site IT, ForwardPass | The workflows the locker runs (for example, Device Loaning or Secure Charging) are created in the FUYL Portal, and it's agreed which bays run which. |
| Test users and device | Site IT | At least one user who can sign in at the Kiosk the way the site does (for example, SSO, a barcode or an RFID card), and a device to test with. |
| Devices (if loading) | Site IT | The devices to load, with their device IDs or asset tags handy. |
| Remote help booked | Site IT or service partner, ForwardPass | A time agreed with ForwardPass for a video call during power-on and onboarding, with whoever's doing it. To book it, submit a support request with the site, date and locker serial numbers. |
What to bring
- A second person. Every locker is a two-person job to move and stand up.
- A trolley, pallet jack or furniture dolly that can take the locker's weight (see Locker weights).
- A box cutter and gloves.
- The model's Quick Start Guide, printed or on a phone (see Quick Start Guides).
- Charging cables for a FUYL Tower, if the order doesn't include them. A FUYL 8 or 23 has its cables built in.
Note: Site IT usually provides the test device, and a laptop or tablet for the video call with ForwardPass. It's worth bringing a spare of each only if they can't.
Install and onboard
1. Receive the locker and accessories
- Check the delivery Count the boxes against the delivery note: the locker, plus any Kiosk Kit, cable retention kits, network kit or wall mount kit that was ordered.
- Look for damage Photograph any damage to the boxes or pallet before signing, and note it on the delivery paperwork.
- Note the serial numbers Write down each locker's serial number and MAC addresses from the packaging (ForwardPass and site IT both ask for these).
- Store it safely Keep it boxed, the right way up as marked, somewhere indoors and dry until it's moved.
If anything's missing or damaged, submit a support request with photos before going any further.
2. Move it to its site
Warning: A large FUYL Locker is around 90kg (200lb), and a small one around 40kg (90lb). Always move one with two people and a trolley or pallet jack, and plan ahead for any stairs.
- Check the route Make sure the boxed locker fits through every doorway, corridor and lift on the way, and that any lift can take its weight.
- Keep it boxed Leave it in its packaging until it's at its final spot, as that protects the doors and display on the way.
3. Unbox it and stand it up
Warning: Standing a locker up takes two people. Keep the doors shut while it's moving, and avoid lifting it by the doors or display, as they aren't built to take its weight.
- Unpack it in place Take off the packaging as close to the final spot as possible, following the Quick Start Guide.
- Stand it up If it's lying down, have one person lift from the top while the other steadies the base, until it's upright and stable.
- Find the accessories The power cable, keys and bay blinds are sometimes packed inside a locked bay rather than a box (the Quick Start Guide shows how to get them out).
- Look it over Check the body, doors, display and bays for damage, and photograph anything found.
- Keep the keys safe The side access door keys open up the locker's internals, so they go to the customer at the end of the visit.
4. Secure it to the wall
Warning: An unsecured locker can tip forward. Secure it to the wall before the Kiosk mount goes on or anything's loaded.
Site facilities prepares the wall ahead of time (drilling and fixings included), so this stage is just positioning, levelling and attaching the locker.
- Position it Move the locker into place against the prepared wall, leaving room for the side access door to open and the cables to reach.
- Level it Adjust the feet until the locker is level, while a second person keeps it steady. Check every door opens and closes freely.
- Secure it Attach the locker to the wall fixings with the hardware included, as shown in the Quick Start Guide. The FUYL Tower 5 can also use the optional Wall Mount Kit (see its Quick Start Guide).
- Route the cables Run the power cable (and Ethernet, if used) to the outlet, out of sight and out of the way. Leave it unplugged for now.
If the wall isn't ready, stop here and let site facilities and ForwardPass know, rather than leaving a loaded locker unsecured.
5. Install the Kiosk mount
Skip this stage if the site isn't using a FUYL Kiosk mount. The Kiosk Kit comes with printed instructions, and FUYL Kiosk Physical Installation covers the same stages with photos and a video.
Note: Have site IT prepare the iPad before it's locked into the mount, since the mount covers the iPad's top button. That means the FUYL Kiosk app installed, Bluetooth allowed for it, and (if the site uses it) Guided Access set up with a passcode site IT keeps. See Installing and Configuring the FUYL Kiosk iPad App.
- Prepare the parts Unscrew or separate anything that's fixed together for shipping.
- Remove the handle Take the handle off the side access door with the handle removal tool.
- Attach the support Bolt the mount support to the side access door.
- Fit the iPad holder Install the holder, and feed the iPad charging cable through the door.
- Install the iPad Fit the iPad into the holder for its generation.
- Tidy the cable Route the charging cable inside the door using the cable management accessories in the kit.
- Close up Close and lock the side access door. On a FUYL Tower 5 or 15, plug the iPad's cable into its charger and the second outlet.
Note: Site IT usually onboards the locker with ForwardPass (stages 6 to 9), and in that case the service partner's part stops here: skip to Hand over. Sometimes ForwardPass goes through onboarding with the service partner instead, and the stages below cover that.
6. Power on and onboard
This is the stage to have ForwardPass on a video call for, with site IT on hand to sign in.
Important: The FUYL Kiosk signs in with an Admin profile on the customer's FUYL Portal account, so site IT signs in themselves. Service partner staff never need an Admin's password, and shouldn't be given one.
- Connect the network Plug the Ethernet cable into the locker, if it's using Ethernet.
- Power on the locker Plug it in and switch it on at the wall. It runs through some self-checks as it starts.
- Check the display It's ready once the display shows Ready to set up with a unique ID. If it shows Enter bay number instead, it needs a firmware update or reset, and ForwardPass can walk through that on the call.
- Sign in to the Kiosk Site IT opens the FUYL Kiosk app and signs in with their Admin profile, choosing the customer's organisation if asked.
- Start the setup Select Set up new station, and allow Bluetooth if asked.
- Select the locker Choose the Locker ID that matches the one on the locker's display.
- Choose network settings Select Use existing tower settings for Ethernet with automatic addressing (DHCP), or New network settings for Wi-Fi or a static address.
- Let it connect The locker connects to the network, the FUYL Portal and then the customer's account. If it gets stuck, check FUYL Networking Requirements with site IT, and ForwardPass can dig into it from there.
- Name the site and group Enter a Site Name (usually the campus or building) and a Group Name (usually the locker itself), using the names agreed with the customer.
- Confirm it's set up The display shows a white LocknCharge logo and the bay lights glow a dim blue, ready for workflows. The Kiosk shows No workflow detected until workflows are allocated, which is normal at this point.
If the Kiosk can't find the locker, see Troubleshooting Bluetooth while Setting up FUYL Enhanced.
7. Allocate workflows
The workflows already exist in the FUYL Portal (see Before the visit), so this stage just gives each bay its workflow.
- Allocate workflows On the Kiosk, select Allocate workflows and authenticate.
- Choose each bay's workflow Pick the agreed workflow for each bay. A bay has to be empty to change its workflow. For bays shared between loans, repairs and deployments, see Dynamic Bays.
There's more on this in Allocating workflows to bays.
8. Load devices (if required)
Only load devices if the customer's asked for it. Loading needs a Technician, Coordinator or Admin role.
- Start loading On the Kiosk, select Load devices and authenticate.
- Load each device Follow the prompts for each bay: identify the device, place it in the bay, and connect its charging cable.
- Shut each door firmly A door that isn't fully closed leaves the bay unlocked.
9. Test each workflow
- Run each workflow Sign in at the Kiosk as a test user and run each workflow once (for example, borrow a device and return it, or start and end a charging session with the test device).
- Check the bays Make sure each bay opens, its light changes, and devices charge.
- Check the FUYL Portal Site IT or ForwardPass confirms the locker shows as online on the Stations page, and the test activity has come through.
- Tidy up End any test loans or sessions, and make sure every loaded device is back in its bay.
10. Hand over
- Hand over the keys Give the side access door keys (and any spare Kiosk Kit keys) to the customer's nominated contact.
- Record the install Note the serial number and location (plus the Site Name and Group Name, if it was onboarded), along with a few photos of the finished install.
- Let ForwardPass know Reply to the support request with those details, so ForwardPass can check everything looks right from the FUYL Portal.
Remove a locker
Use these stages when a locker is leaving a site for good. Clear the bays first, while the locker is still online and on the customer's account. That way open loans and sessions close properly, and every bay can be opened from the Kiosk.
1. Open and clear every bay
Important: Anything left in a locker leaves with it, so agree with site IT where every device goes before opening a bay.
- End active workflows Site IT or ForwardPass ends any active loans, repairs or charging sessions in the FUYL Portal, so the device records are closed off.
- Open View tower On the Kiosk, select the cog , authenticate, then select View tower.
- Unlock each bay Select Unlock bay next to each bay in turn.
- Remove the devices Take out every device and hand them to site IT. The locker's own cables and bay blinds stay with the locker.
- Close every door Shut each bay once it's empty.
If the locker or Kiosk is offline, the bays can still be opened with the manual release pins behind the side access door. See Accessing Bays as an Administrator.
2. Remove it from the customer's account
A locker that's still on an account reconnects to it automatically whenever it finds a network, so it needs removing from the account before it's reset.
- Request removal One of the customer's Admins removes the locker from the FUYL Portal, or asks ForwardPass to do it for them by submitting a support request with the serial number.
- Remove the Kiosk Unless the Kiosk is moving to another locker, its station group is removed at the same time.
- Wait for confirmation Hold off resetting or powering down the locker until the removal's confirmed.
3. Factory reset the locker
A factory reset clears the locker's network settings and takes it back to Ready to set up, so it's ready to be set up somewhere else. Removing the locker from the account may already have reset it, but resetting it again is safe.
- FUYL 8 and FUYL 23: Open the side access door, pull the display door release pin and open the display door. Press and hold the reset button on the back of the display door for 10 to 15 seconds, until the display confirms the reset.
- FUYL Tower and FUYL Tower Pro: On the keypad, press 00 then OK and enter an admin PIN. Select Danger zone > Factory reset, then OK to confirm. If no admin PIN works, ForwardPass can talk through the hardware reset for that model.
Once it restarts, check the display shows Ready to set up.
4. Power it down
- Check every bay Make sure every bay is empty and closed.
- Switch off the locker Switch it off at the wall, then unplug the power cable.
- Disconnect the rest Unplug the Ethernet cable (if used), and on a FUYL Tower 5 or 15, the Kiosk iPad's charger.
5. Remove the Kiosk iPad
The iPad usually belongs to the customer, so it stays on site.
- Open the side access door Unlock it with the key.
- Take out the iPad Remove it from the holder (the reverse of installing it), and disconnect its cable.
- Hand it to site IT Site IT turns off Guided Access with their passcode and removes the FUYL Kiosk app, or resets the iPad through their MDM.
6. Remove the Kiosk mount
- Remove the holder Unbolt the iPad holder and pull the charging cable back through the door.
- Remove the support Unbolt the mount support from the side access door.
- Refit the handle Put the original handle back on the side access door, if it was kept.
- Keep the parts together Bag up the mount, bolts, cable and keys together, in case the kit gets reused.
7. Detach it from the wall
Warning: Once the bracket's off, there's nothing stopping the locker tipping, so have one person steady it while the other works.
- Detach it Undo the wall hardware while the second person holds the locker.
- Move it clear Ease the locker away from the wall. Removing the fixings and patching the wall is up to site facilities.
8. Remove it from site
- Lock it up Close every bay and lock the side access door, so nothing swings open on the way out.
- Protect it Repack it in its original packaging if there is any, or wrap it to protect the doors and display.
- Move it safely Use two people and a trolley or pallet jack, the same as for the install.
- Take the accessories Take the power cable, Kiosk mount and any kits, but leave the iPad (and its charger) with the customer.
9. Confirm what happens next
Before collection, check with ForwardPass what happens to the locker next (for example, return to a ForwardPass warehouse, reuse, resale or recycling). Please don't dispose of a locker or any of its parts without that confirmation, and since they're full of electronics, any recycling needs to follow local e-waste rules.
Reference
Locker weights
| Locker | Approximate weight |
|---|---|
| FUYL 15 and FUYL 23 (large) | 90kg (200lb) |
| FUYL 5 and FUYL 8 (small) | 40kg (90lb) |
Quick Start Guides
- FUYL 8 and FUYL 23 Quick Start Guide (PDF)
- FUYL Tower 5 and 15 Pro Quick Start Guide (PDF)
- FUYL Tower 5 and 15 (MK2) Quick Start Guide (PDF)
- Guides for the cable retention, wall mount and network kits are in Installing FUYL Accessories.